Collion Webshop/TAG-CONNECT/Legged Version products

TC2030-CTX-NL-LEMTA 59,50 €

Thu, 16 Jul 2026 13:02:28 +0200

6-poliges "No Legs" TC2030 Plug-of-Nails™ Kabel für ARM Cortex Prozessoren.

Special Version for ATMEL-ICE programmer/debugger. ATMEL-ICE contains a converted connector orientation !

Diese spezielle Kabelversion besitzt einen 6 poligen TC2030-NL Tag-Connector sowie einen 10 poligen Flachbandkabel Connector welcher zum Anschluss des FTSH-105 Mikrostecker für Cortex Debugging passt wie er beispielsweise bei Keil´s ULINK-2 Debugger zu finden ist.

das TC2030-CTX-NL Plug-of-Nailstm Connector Footprint spart über 66% Platinenfläche verglichen mit dem Einsatz des Standard FTSH-105 Mikrostecker Footprints.

Die Details des Footprint entnehmen Sie bitte dem Datasheet des TC2030-NL.

See also the TC2030-CTL "Legged" version of the cable.

For traditional ARM JTAG solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.

Der abgebilte Keil ULINK2 Debugger, sowie die Tag-Connect Demo PCB sowie das zusätzliche "Legged" Kabel dienen lediglich der Illustration und sind nicht Bestandteil des Artikels!

TC2030-FTDI-TTL-232R-3V3 89,25 €

Thu, 09 Jul 2026 18:02:07 +0200

Der Tag-Connect FTDI TTL to USB Serial Converter verfügt PCB-Boardseitig über einen 6Pin Connector mit "Legs".
Der Signalpegel der seriellen Signale beträgt 3,3V und kann dementsprechend mit einer Vielzahl an Mikrocontrollern ohne zusätzlichen Einsatz eines Pegelkonverters eingesetzt werden.

TC2030-ALT 77,35 €

Mon, 27 Oct 2025 16:11:35 +0100

The TC2030-ALT cable is a special cable that has a TC2030 Tag-Connector at one end and a 10-pin 0.1" pitch female IDC connector at the other.

The 10-pin IDC can be plugged directly into some Altera USB Blasters and ByteBlasters.

The cable is wired as follows:

TC2030-ALT Connections
TC2030	10-pin 0.1" IDC
1	4 Vref
2	5 TMS
3	9 TDI
4	1 TCLK
5	2,10 GND
6	3 TDO

Please refer to the TC2030-IDC datasheet for details of the TC2030 connector and footprint.

TC2030-FTDI-TTL-232RG-VIP 89,25 €

Mon, 01 Jun 2026 14:19:41 +0200

TC2030-FTDI-TTL-232RG-VIP USB to TC2030 Serial Cable

The Tag-Connect FTDI TTL to USB Serial Converter features a 6-pin tag-connect connector with “legs” on the PCB side.
In this version, the signal level of the serial lines can be set to match the board’s I/O voltage between 1.8 V and 5 V by means of the VCCIO pin.

FTDI-TTL-232RG-VIP Specification
VCC: 1.8V to 5.25V
UART TTL level signals: VCC
Data rates: 3Mbps
Notes: VCC is a required Input, UART signal output levels match VCC and won’t be present if VCC is not connected

Nominal cable length: 1.8m.

TC2030 Connections

TC2030 pin	FTDI Signal	Type	Description
1	VCCIO (RED)	Input	VCC input. Power and voltage levels for the UART signals are supplied from the customers interface logic
2	CTS / TMS (BROWN)	Input	Clear to Send Control input / Handshake signal
3	RXD / TDI (YELLOW)	Input	Receive Asynchronous Data input
4	TXD / TCLK (ORANGE)	Output	Transmit Asynchronous Data output
5	GND (BLACK)	GND	Device ground supply pin
6	RTS / TDO (GREEN)	Output	Request To Send Control Output / Handshake signal

TC2070-IDC 77,35 €

Tue, 07 Jul 2026 22:33:56 +0200

Fitted with 14-pin (2x7) 0.1" spaced ribbon cable connector. Approx 8" of ribbon cable between connectors.

Legged version

TC2030-MCP 59,50 €

Tue, 11 Jun 2024 08:40:58 +0200

6" version of the TC2030-MCP cable

TC2030-CTX-20 65,45 €

Thu, 21 May 2026 08:38:48 +0200

This cable is the same as the TC2030-CTX cable except it has a 20-pin connector compatible with i-Jet and ULINK pro.

The cable itself has a ten pin ribbon cable and 6-pin TC2030 Tag-Connect footprint supporting ARM Cortex MCU's.

Please refer to the TC2030-CTX datasheet. IAR's I-JET not included!

ARM20-CTX 45,22 €

Wed, 22 Jul 2026 10:45:53 +0200

The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Single Wire Debug) applications.

Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 6-pin 0.1” ribbon headers on their PCB instead of the traditional 20-Pin header.

TC2050-IDC-430 59,50 €

Wed, 04 Oct 2023 08:21:49 +0200

Tag-Connect’s TC2050-IDC-430 cable is a special version of the TC2050-IDC Plug-of-Nails™ cable designed to be plugged directly into TI’s MSP-FET430 and is compatible with all MSP430 MCU’s.

The cable is fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 14-pin 0.1” ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny footprint of pads and locating holes in your PCB. Footprint MUCH smaller than the standard 14-pin ribbon header.
Zero Cost Per Board!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and reduces the size and space requirements of your PCB.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB’s while lowering board costs and facilitating efficient production programming.
Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB.
Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 14-pin ribbon connector on the other and is wired specifically for the TI MSP-FET430 debugger (and compatible MSP430 debuggers).
It is compatible with all MSP430 MCU’s.
See also TC2050-IDC-430 NL (no-legs) version with a tiny 0.03” footprint.

Also, if your MSP430 device supports SPY-BI-WIRE, take a look at the SPY-BI-TAG adaptor with the even smaller footprint TC2030-MCP 6-pin cables.

For full specifications, please download the TC2050-IDC-430 Datasheet (pdf) Also available in space-saving “no-legs” version. See TC2050-IDC-NL-430

TC2050-IDC 53,55 €

Fri, 24 Jul 2026 20:02:30 +0200

Tag-Connect’s TC2050-IDC Plug-of-Nails™ cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1” ribbon connector.

Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny footprint of pads and locating holes in your PCB.
Zero Cost Per Board! Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space. Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB’s while lowering board costs and facilitating efficient production programming.
Tag-Connect uses a patented specially designed connector which eliminates the need for putting a programming header or other mating connector on every PCB.
Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1” ribbon connector on the other and is suitable for use with most many MCU’s / FPGA’s and JTAG programming and debug operations.

A growing range of adaptor cables are available for use with various applications, such as ARM MCU's, Xilinx SPARTAN and VERTEX FPGA’s, TI MSP430 (TC2050-IDC-430) and Renesas MCU's compatible with E1/E8a debuggers.

For full specifications, please download TC2050-IDC Datasheet See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint

TC2050-IDC-050-ALL 77,35 €

Fri, 16 Jan 2026 13:49:23 +0100

TC2050-IDC-050-ALL

TC2050-IDC-NL-050-ALL 77,35 €

Mon, 02 Feb 2026 13:57:28 +0100

TC2050-IDC-NL-050-ALL

TC2050-IDC-NL-050-STDC14 78,54 €

Tue, 21 Jul 2026 10:10:08 +0200

C2050 10 Pin “No Legs” Plug-of-Nails™ to 0.050″ pitch 14 pin ribbon connector suitable for STLINKV3 and STLINK-V3MINI debuggers that connects to the STDC14 connector.

TC2030-CTX 59,50 €

Thu, 16 Jul 2026 12:57:02 +0200

TC2030 cable with Leg´s for ARM Cortex debug

This cable combines Dies ist eine Kombination eines 6 Pin TC1030 Stecker und einem 10 poligen Flachband- kabel und Konnektor, welcher mit dem TSH-105 Stecker des Cortex Debug Konnektor kompatibel ist welcher beispielsweise auf Keil´s ULINK-2 eingesetzt wird. Datasheet: http://www.tag-connect.com/Materials/TC2030-CTX.pdf See also the TC2030-CTL-NL "No Legs" version of the cable with footprint that saves over 66% of the board space needed by typical FTSH-105 micro headers!

For traditional ARM solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.

Keil's ULINK2 debugger and Tag-Connect Demo PCB for illustrative use - not included with the cable!

TC2030-IDC-10 47,60 €

Tue, 28 Apr 2026 05:05:11 +0200

"Leg" Version of the TC2030-IDC cable with in 10" (25,4cm) cable length

TC2030-IDC 47,60 €

Thu, 16 Jul 2026 12:58:55 +0200

"Leg" Version of the TC2030-IDC cable with 6" (15,24cm) cable length

TC2030-MCP-10 59,50 €

Tue, 09 Dec 2025 10:49:21 +0100

This is the 10" (longer) version of the TC2030-MCP cable.
Note that 10" exceeds the Microchip maximum cable length specification of 8" and is not supported by Microchip.
However, the additional length provides increased convenience and has not been known to cause problems in general use. Microchip to date has only specified the maximum length of the programming cable and not the typical additional length of PCB traces needed between the RJ12 connector (which might be on the edge of the PCB) and the MCU. With the much smaller TC2030 footprint you can usually put the ICD connection right at the MCU.

ECV3-06-IDC 101,15 €

Thu, 16 Jul 2026 13:03:47 +0200

ECV3-06-IDC 6-pin Castellated Board-Edge Connector to 6-pin (2*3) IDC connector

6-pin Castellated Board-Edge Connector to 6-pin 0.1″ pitch ribbon connector.

ECV3-10-IDC 104,72 €

Thu, 09 Jul 2026 13:40:20 +0200

ECV3-10-IDC 10-pin Castellated Board-Edge Connector to 10-pin IDC

10-pin Castellated Board-Edge Connector to 10-pin 0.1″ pitch ribbon connector.

ECV3-10-IDC-050-20 101,15 €

Mon, 09 Mar 2026 11:30:40 +0100

ECV3-10-IDC 10-pin Castellated Board-Edge Connector to 20-pin (2*10) connector (1.27mm)

10-pin Castellated Board-Edge Connector to 10-pin 0.05″ pitch ribbon connector.